SeamanU.S. Government Printing Office, 1951 - 253 sivua |
Muita painoksia - Näytä kaikki
Yleiset termit ja lausekkeet
ahead aircraft ammunition anchor anchor watch awning battery boat boatswain's boatswain's chair bolt boom bowline breech buoy caliber called CARRICK BEND cartridge chain CHAPTER charge cleat clove hitch coil crew davits deck electric engine eye splice fathoms fender Figure firing pin fore and aft forward front sight fuze gangway gantline gasoline gear HALF-HITCH halyard hand handle hangfire hauled heaving hoisted hook keep knot ladder light loaded lookout lower magazine marlinspike mast mooring line mount Navy never officer operation outboard paint pistol pointer port powder PRIMER projectile pull range rear rifle rope rudder running running rigging safety precautions sail seaman secured shackle shellman ship ship's side slack slide speed splice starboard station steering stern stoppers strakes strand surface swing tank target topping lift towing Training trigger turn turret usually vessel watch whaleboat whip wire wire rope yards
Suositut otteet
Sivu 67 - In obeying and construing these rules due regard shall be had to all dangers of navigation and collision, and to any special circumstances which may render a departure from the above rules necessary in order to avoid immediate danger.
Sivu 63 - That the following regulations for preventing collisions shall be followed by all vessels navigating all harbors, rivers, and inland waters of the United States, except the Great Lakes and their connecting and tributary waters as far east as Montreal and the Red River of the North and rivers emptying into the Gulf of Mexico and their tributaries, and are hereby declared special rules duly made by local authority: SEC.
Sivu 203 - ... insert the lug on the collar in the undercuts in the extractor by pushing the extractor to the rear until its tongue comes in contact with the rim on the face of the bolt (a slight pressure with the left thumb on the top of the rear part of the extractor assists in this operation) ; turn the extractor to the right until it is over the right lug ; take the bolt in the right hand and press the hook of the extractor against the butt plate or some rigid object, until the tongue on the extractor enters...
Sivu 204 - Insert the follower and magazine spring in the magazine, place the tenon on the front end of the floor plate in its recess in the magazine, then place the lug on the rear end of the floor plate in its...
Sivu 200 - The bolt can not be drawn fully back, and its front end projecting over the rear end of the upper cartridge holds it down in the magazine below the action of the bolt. The magazine mechanism then remains inoperative, and the arm can be used as a single loader, the cartridges in the magazine being held in reserve.
Sivu 199 - ... draw the bolt fully to the rear, insert the cartridges from a clip, or from the hand, and close the bolt. To charge the magazine from a clip, place either end of a loaded clip in its seat in the receiver and, with the thumb of the right hand, press the cartridges down into the magazine until the top cartridge is caught by the right edge of the receiver. The...
Sivu 204 - ... the safety lock can be turned to the vertical position with the right hand ; insert the firing pin in the bolt and screw up the sleeve (by turning it to the right) until the sleeve lock enters its notch on the bolt.
Sivu 23 - To take charge of this post and all Government property in view. 2. To walk my post in a military manner, keeping always on the alert and observing everything that takes place within sight or hearing. 3. To report all violations of orders I am instructed to enforce. 4. To repeat all calls from posts more distant from the guardhouse than my own. 5. To quit my post only when properly relieved.
Sivu 203 - Grasp with the left hand the rear of the bolt, handle up, and turn the extractor collar with the thumb and forefinger of the right hand until its lug is on a line with the safety lug on the bolt...
Sivu 136 - When painting overhead surfaces, the ceiling panels should, as far as possible, be laid off fore and aft, and the beams athwartship. Where panels contain a great many pipes running parallel with the beams it would be difficult to lay off the ceiling panel fore and aft. In such cases better results will be obtained by laying off parallel with the beams.